⚝ FREE WORLDWIDE EXPRESS SHIPPING ⚝
Pneumatic Dent Puller
$84.95 USD$210.00 USD
Color: 1× Dent Puller + 3 Cup Sizes
Product Details
Garage-Ready Auto Tool
Pull the Dent Yourself. Keep the $650.
A pneumatic dent puller that hooks to the air compressor you already own and walks shallow dents back out in about 60 seconds — no glue, no drilling.
✔ Pops most dents in 60 seconds — seal, pull, pop
✔ No glue, no drilling — paint-safe vacuum grip only
✔ 3 cup sizes — door dings to palm-size dents
✔ Runs off any garage air compressor, even a small pancake unit
A $650 Quote for a Ding You Could Barely See
A shopping cart taps your door. A hailstorm peppers the hood. You take it to the body shop expecting a couple hundred bucks and walk out with a quote that makes you wince — for a dent you can barely see unless the light hits it right.
The usual DIY options aren't much better. Hot-glue kits leave residue and can lift your clear coat when you twist the tabs off. Stud welders put actual holes in your panel to pull it back.
You end up paying full body-shop money for damage that's really just cosmetic.
The Same Vacuum Principle Body Shops Use — Sized for Your Garage
Aerova connects to your air compressor with a standard 1/4" quick-connect. Flip the lever, and the brass valve builds real pneumatic vacuum grip on the panel — no glue, no heat, no drilling. Clean the panel, seal the cup over the dent, and work the slide hammer with steady pulls. Most first-timers see the dent moving within 60 seconds.
"The body shop wanted $650. This pulled it in my driveway."
— Verified Customer
What Changes Once It's in Your Garage
Factory paint stays factory paint
No glue residue, no lifted clear coat, no drilled holes — just vacuum grip on a clean panel.
Pays for itself on the first pull
One tool costs less than a single body-shop panel repair, and it's ready for the next ding too.
No waiting room, no drop-off
Pull the dent in your own driveway on your own schedule — no appointment, no rental car.
Handles more than one type of damage
Three cup sizes cover door dings, shopping-cart hits, and shallow hail damage across a full panel.
No experience needed
If you can hook up an air hose, you can run this — connect, seal, pull.
Pop the Dent Back Out in 3 Steps
1. Connect and set your PSI
Snap the 1/4" quick-connect onto your compressor hose. Set to 90–100 PSI for the strongest grip.
2. Seal the cup over the dent
Clean the panel first so the rubber seals properly, then choose the cup size that matches your dent.
3. Open the valve and pull
Work the slide hammer with steady pulls, starting from the shallow edge and working inward.
Built Like a Shop Tool
| All-metal body, brass valve | Built to hold pressure and last through repeated use, not a one-off gadget |
| 3 interchangeable cup sizes | Matches the cup to the dent instead of forcing one size to do everything |
| 23-inch reach | Enough leverage to work larger panels without straining your grip |
| Standard 1/4" quick-connect | Works with the compressor already sitting in your garage |
Aerova vs. The Alternatives
| Aerova | Hot-Glue Kits | Body Shop | |
| Paint-safe (no glue, no heat) | ✔ | ✘ | ✔ |
| Ready in about 60 seconds | ✔ | ✘ | ✘ |
| One-time cost under $70 | ✔ | ✔ | ✘ |
Frequently Asked Questions
Will it work on my dent?
It's built for door dings, shopping-cart hits, parking bumps, broad panel dents, and shallow hail damage. If the paint is intact and the dent has no sharp crease, it's a good candidate.
Do I need an air compressor?
Yes — it connects with a standard 1/4" quick-connect fitting. Even a small pancake compressor has enough air, since it draws in short bursts.
What PSI should I run it at?
Set your compressor to 90–100 PSI for the strongest grip.
Will it damage my paint?
No — the cup grips with pneumatic vacuum only, no glue, drilling, or heat. Clean the panel first so the rubber seals well, and release the valve before lifting the cup off.
Which panels does it work on?
Steel and aluminum body panels — doors, fenders, hoods, quarter panels, tailgates, and roofs. It's not for plastic bumpers, trim, or glass, since plastic flexes instead of holding a vacuum seal.
Do I need experience to use it?
No. If you can hook up an air hose, you can use it. Connect, seal the cup, open the valve, and work the slide hammer with steady pulls — most people see the dent moving within 60 seconds.
Skip the Body Shop Quote
Hook it to the compressor you already own and pull your first dent this weekend. Backed by a 30-day money-back guarantee.
12,000+ SOLD · 4.8/5 RATED
Worldwide Free Shipping
Over 4 Million Happy Customers
Award-Winning Customer Support
Share on: